News Topic

iMag Seametrics Magnetic Flow Meter


The iMAG-Series is the most economical flanged electromagnetic flow meter on the market. It is used in 3” to 12”pipe in municipal or industrial water, waste water, pump stations and packaged plant applications. The iMAG has no moving parts and electrodes are designed to discourage fouling. This magmeter requires no maintenance in applications where debris would impede mechanical meters. There are no parts to wear out. Minimal straight pipe requirements allow iMAG-Series meters to be used in piping configurations where there is little space between the meter and an elbow.

iMAG-Series flowmeters are rated IP68 for applications where the meter may be under water up to a depth of 10 feet (3 meters) for prolonged periods of time. Rate and total indication are standard. Rate and total units and pulse output are settable via the front panel touch key pad by the user. The iMAG can be externally powered with 9-36 Vdc at 30 mA. The standard 20-foot (6 meter) cable also provides outputs for use with a variety of Seametrics and other displays and controls for remote reading, data logging and telemetry applications. 4-20mA passive current loop and high frequency outputs are optional. The iMAG 3600 remote display flowmeter can be supplied with an optional internal AC power supply.


Positioning the Meter. 

These flowmeters can be installed horizontally, vertically, and in any radial position. Using a check valve on the upstream side of the meter, and/or an air vent (vacuum relief valve) in the same, unobstructed run of pipe as the meter, is required in any installation where the meter may be exposed to suction when the system is not in normal operation. Suction can cause damage to the liner. Liner damage caused by suction, without the use of a check valve and/or air vent, may void the warranty. Straight Pipe Recommendations. As with most flow meters, the iMAG requires straight pipe before and after the meter for best accuracy. However, the ability of electromagnetic meters to average the flow across the entire pipe allows for shorter straight pipe recommendations than most mechanical meters 

Full Pipe Recommendations. All magmeters require a method for determining that the pipe is empty, to prevent false reading. This meter is designed to indicate ‘EMPTY PIPE’ if one or more electrodes is exposed. For highest accuracy, install the meter so that the pipe will be full when there is flow. If air bubbles may be present in the pipe or sludge accumulation is an issue, rotate the meter by one flange hole to position the control housing at a 45˚ angle 

  • Easy set up
  • Minimal straight pipe
  • Mounted or remote rate & total
  • Tamper-evident seal
  • NSF-61 approved
  • IP68 rated


  •  Water & Waste Water Treatment
  • Municipal
  • Treatment plants
  • Pump stations
  • Packaged plants
  • Filtration systems


Pipe Size
3”,4”, 6”, 8”, 10”,12”
150 lb. ANSI pattern
150 psi (10.3 bar) working pressur
10˚ to 130˚ F (-12˚ to 54˚ C)

-40˚ to 158˚ F (-40˚ to 70˚ C)
+/- 1% of reading +/- 0.25% of full-scale flow from low flow cutoff to maximum flow rate of 10 m/se
Low Flow Cutof
0.5% of maximum flow rat
 Body (3” Only)
Ductile cast iron, powder-coated w/NSF61 listed epoxy powde

      Body (4”-12”
Welded steel, epoxy-coated

      Liner (3” Only 

       Liner (4”-12”)

      Electronics Housing
Ductile cast iron, powder-coate

316 stainless stee

      O-ring (3” Only)
128×64 dot-matrix LCD

5 Digit Rate

Rate Volume Units
Rate Time Units
Total Volume Units

Cubic Feet
Cubic Meters
Million Gallons
Mega Liters
Imperial Gallons
Million Imperial Gallons
Gallons x 1000
Million Gallons
Liters x 1000
Mega Liters

Cubic Meters
Cubic Meters x 1000
Cubic Feet
Cubic Feet x 1000
Imperial Gallons
Imperial Gallons x 1000
Million Imperial Gallons
DC Power
9-36 Vdc @ 250 mA max, 30 mA average

AC Power
85-264Vac, 50/60Hz, 0.12A
Telemetry Output
3.3V asynchronous receive and transmit (UART) signals, ASCII command-response protocol
Pulse Frequency Output
Current sinking pulse, isolated, 36 Vdc at 10 mA max

Pulse Rates
User-settable volume units/pulse. Pulse width is one-half of pulse period, 200 pulses/sec max
4-20mA Current Loop
Isolated, passive, 6-36Vdc, +/- 0.1% of pulse/frequency output HART compliant2

Digital Output
Isolated, open collector, 36Vdc @ 10mA max., frequency output up to 10kHz

Relay Output
Solid state relay, normally open, non-polarized, 28Vac/40Vdc @ 0.5A max, 33Hz max

Serial Communications2
Isolated, asynchronous serial RS485 or RS232, Modbus RTU protocol
Control Cable
Six-conductor water-blocked cable, polyurethane jacket, 20ft (6m) standard length for power, pulse
frequency or optional outputs. Optional lengths up to 100’ available

Remote Display Cable (iMAG 3600)
33ft (10m) standard length may be shortened (by user in the field). Additional cable can be ordered and attached with the use of a junction box (purchased from a standard supplier) up to 100ft (30m) total
>20 microSiemens/cm
Empty Pipe Detection
Hardware/software, conductivity-based
(EN 61326) pending, NSF-61
IP68 to 10ft (3m) depth


Article Flowmasonic: Rudy flow meter Wiratama

Flow Meter Air Baku PDAM

Flow meter air baku pdam adalah flow meter yang digunakan untuk mengukur debit air dan total volume air baku yang akan di proses guna menghasilkan kwalitas air sesuai standart pdam. Air baku pdam bisanya dimabil dari sungai, bendungan, waduk atau sumur bor dan untuk daerah tertentu mungkin mengambil dari air laut yang di proses menjadi […]

Thermal Mass Compress air and gas flow meters VA500

Flow sensor for compressed air and gas – VA 500 Contrary to the previously used bridge circuit the newly developed evaluation electronics of our flow sensor records all measured values digitally. This leads to a better accuracy also in case of large measuring spans of 1:1000. What are the advantages of our flow measuring technology? […]

Flow meters for compressed air and gas

Fow meters from CS Instruments work according to the calorimetric measuring principle. This means, while measuring the thermal mass flow or standard volume flow, no additional temperature and pressure compensation is necessary. The standard volume is a common volumetric unit used to compare gas quantities at different pressures and temperatures. In order to meet various […]

Batch Controller N series fluidwell

The product group “Batch Controllers” offers multiple batch controllers in the N-Series, F-Series and D-Series product ranges. The batch controllers can be used for accurate dispensing of small amounts of liquids up to the loading of trucks with two-stage control and analog multi-stage control. Specially designed for the delivery of unknown quantities of product is […]

Flow Computers fluidwell

The product group “Flow Computers” offers a unique range of comprehensive solutions to calculate the consumption and net flow at standard conditions or the ratio between two flows. Typical applications are found on board of ships to calculate the fuel consumption, gas flow calculation in power plants and the monitoring of two component blending. The […]


Ada yang ingin ditanyakan silahkan

1. Jika ada Pertanyaan tentang Product ataupun harga silahkan langsung hubungi :

2.  Jika ada pertanyaan atau diskusi Tentang tulisan disini silahkan email ke :  

  Atau silahkan isi kolom dibawah ini dan klik submit      

%d bloggers like this: