The common rail system, as the name suggests, is a system that is common for every cylinder or unit of the marine engine. Marine engines of the early times had a fuel system, wherein each unit had its own jerk pump and the oil pressure was supplied through the jerk pumps.
However, in the common rail system, all the cylinders or units are connected to the rail and the fuel pressure is accumulated in the same. The supplied fuel pressure is thus provided through the rail. A similar type of common rail system is also there for servo oil system for opening of the exhaust valves.
Speaking about the fuel injection system, the common rail system was launched even before the jerk pumps but was also not successful because of a few drawbacks. However, because of some latest advancements in technology and electronics, the common rail system has gained popularity.
The common rail engines are also known as smokeless engines as fuel pressure required for combustion is same for all loads or rpm of the engine.
The common rail is employed in the following system :
1). for heated fuel oil at a pressure of 1000 bars.
2). for servo oil for opening and closing of exhaust valves at a pressure of 200 bars.
3). control oil for opening and closing of valve blocks at a pressure of 200 bars.
4). compressed air for starting main engine.
Main Components of Common Rail System
The common rail system consists of a high-pressure pump which can be cam-driven or electrical driven or both. Pressure requirement will be different for a different systems. For fuel oil the pressure are as high as 1000 bars, for servo and control oil the pressure is about 200 bars. The high pressure pumps are driven by camshaft with three lobe cams. These pumps makes several stroke with the help of three lobe cams and speed increasing speed gear.
For fuel oil and servo oil the pumps are engine driven and for control oil it is motor driven.
A fuel oil rail.
B is the control oil rail.
C servo oil rail.
D Injection control unit (ICU).
E Valve control unit (VCU).
This is provided after the pumps where the accumulated pressure from the pumps is provided to the rail which supplies them to each unit when required. This is located at the engine,s top platform and just below the cylinder cover. These rail units extends to full length of the engine. These are enclosed in the case and have access from the top for maintenance and overhauls.
Valve Block and Electronic control system
This is required for the control of the flow of the fuel oil, servo oil, control oil and starting air from the rail to the cylinder. The valve block is operated by the electronic control which operates when it gets a signal indicating that this cylinder is at top dead centre (TDC) and fuel has to be injected and decides when exhaust valve has to be opened. With the help of electronics the injection can be controlled remotely from the computer. For e.g. if we want to cut off fuel to one of the unit, then we need to cut off the signal given from the control system so that the valve will not open.
The fuel oil system this block is known as ICU ( Injection control Unit) and for the exhaust valve, it is known as VCU (Valve Control Unit). The control system for opening and closing of ICU and VCU is done by electro hydraulic control with which when the signal for open is present the valve for control oil opens and control oil pushes the valve of ICU and VCU to open. The signal for electronic control is given by a crank angle sensor that senses about each cylinder and sends a signal to a system that decides whether to open a valve or close the valve.
The timing of the opening of the valve can also be controlled by the electronics, which means that if the signal is given to open the valve early it will open early and vice versa.
Advantages of Common Rail over Conventional Jerk Pump System
The following are the advantages of the common rail system :
1). Same injection pressure for the engine at all loads or rpm which is not possible in jerk pumps as the later is dependent on the engine speed.
2). Injection timing can be varied during running of the engine, whereas in conventional system the engine has to be stopped and setting for timing has to be changed.
3). The design of common rail is simple as there are no individual fuel pumps and cams for each fuel pump are also removed.
4). The common rail gives smokeless operation whereas in conventional system smokeless operation is only during high rpm.
5). Reduced maintenance is required because of less number of pumps and increased efficient combustion time between overhauls.
6). With this system control of variable opening of exhaust valve can also be done which is not there in traditional system.
for further please contact us, email@example.com