Advertisements
News Topic

Coriolis Flow Transmitter RHE

Inside the measuring sensor, there are precision tubes that are energized by an electromagnetic drive system, which itself is fed by the transmitter, to vibrate at their natural frequencies. When a liquid or gas flows through the vibrating tubes, it is subjected to additional deflection due to the degree of inertia that is generated. This deflection is recorded electronically by two velocity sensors and a high-precision electronic time delta. This measured quantity is proportional to the mass flow rate.

Coriolis mass Flow Controls

A further conversion into physical units is done in a purely digital manner using a signal processor in the transmitter. At the same time, all of the appliance’s functions are constantly monitored. Should any disruptions occur, all of the errors that have occurred are immediately reported in the display.

The transmitter has a 4 to 20 mA analogue output with programmable span, which is proportional either to the measured mass flow rate or the temperature; it also has an impulse output that supplies mass-proportional impulses. All of the outputs and measuring functions can be verified at any time by the user by using the diagnostic mode in the appliance. The maintenance or new calibration intervals can be monitored via a run-time counter. For service or repair purposes, the transmitter and flow sensor can be replaced independently of each other.

Coriolis mass flow Transmitter

This significantly reduces the costs of spare parts for the installed flow sensor/transmitter. During the factory calibration, the mass flow sensor can be calibrated independently of the transmitter. All sensor-specific calibration data can be programmed using magnetic switches located on the front panel. To achieve this, the instrument does not need to be opened. All of the relevant data is buffered in a non-volatile semiconductor device (EEPROM).

The RHEONIK mass flow meter consists of one of the RHM series flow sensors and one RHE series transmitter. The remote unit RHE 07/08 is for installation in a safe non-Ex area and is connected to the sensor via a single multi-conductor cable. Please note, that the types RHE 07/08 and all sensor articles are available in non Ex-versions (without Exnameplate). The RHE 11 (Ex d) may be installed and operated in hazardous Ex-areas (Zone 1 or 2). Ex-series sensors RHM (with Ex-Label) are, when connected with an Ex- Transmitter, made for installation inside hazardous areas (Ex-zone 0, 1 or 2). The transmitter RHE includes seven printed boards which can be replaced during servicing. The remote electronic unit consists of two bent measuring loops in the shape of an omega.

Kind of Coriolis Flow Transmitter

  • RHE 07

The RHEONIK mass flow meter consists of one of the RHM series flow sensors and one RHE series transmitter. The remote unit RHE 07/08 is for installation in a safe non-Ex area and is connected to the sensor via a single multi-conductor cable. Please note, that the types RHE 07/08 and all sensor articles are available in non Ex-versions (without Exnameplate). The RHE 11 (Ex d) may be installed and operated in hazardous Ex-areas (Zone 1 or 2). Ex-series sensors RHM (with Ex-Label) are, when connected with an Ex- Transmitter, made for installation inside hazardous areas (Ex-zone 0, 1 or 2). The transmitter RHE includes seven printed boards which can be replaced during servicing. The remote electronic unit consists of two bent measuring loops in the shape of an omega.

  • RHE08

The RHEONIK mass flow meter consists of one of the RHM series flow sensors and one RHE series transmitter. The remote unit RHE 07/08 is for installation in a safe non-Ex area and is connected to the sensor via a single multi-conductor cable. Please note, that the types RHE 07/08 and all sensor articles are available in non Ex-versions (without Exnameplate).

  • RHE11

The RHE 11 (Ex d) may be installed and operated in hazardous Ex-areas (Zone 1 or 2). Ex-series sensors RHM (with Ex-Label) are, when connected with an Ex- Transmitter, made for installation inside hazardous areas (Ex-zone 0, 1 or 2). The transmitter RHE includes seven printed boards which can be replaced during servicing. The remote electronic unit consists of two bent measuring loops in the shape of an omega.

  • RHE12

The RHE 12 transmitter is equipped with a 24 VDC mains supply. For trouble-free operation, the power supply must maintain the specified nominal voltage of +- 10%. When connecting the transmitters, always ensure that the power supply is switched off. The earthing for the power supply should be connected using the relevant RHE earthing.

  • RHE14

 The  RHE14  is  low  cost,  compact  and  ideal  for  OEM applications. I/O includes 4-20mA, pulse, flow direction and RS232 serial data. Programming and configuration by SensCom™ software. The RHE06 is ATEX approved for hazardous area installation  and  offers  pulse  output  and  Error  and  Flow Direction.  *The  RHE06F+  has  double  pulse  outputs with 90° phase shift for custody transfer applications

Advertisements

Articles: Flow meters Wiratama

Jenis dan model flowmeter magnetic

Jenis flow meter magnetic Flowmeter magnetic diproduksi dan digunakan hanya untuk mendeteksi aliran yang mempunyai dasar ciran yang mempunyai koduktivitas minimal 20 micro siemens. Sensua dengan aplikasinya jenis flowmeter magnetic dapat di golongkan berdasarkan cara installasinya yaitu In Line flow meter magnetic Insertion magnetic flow meter In Line flow meter magnetic In Line magnetic flow meter […]

Komponen flow meter magnetic

Flow sensor magnetic Ada dua komponen flowmeter magnetic yang utama yaitu magnetic flow sensor dan magnetic flow transmitter atau converter magnetic. Untuk flow sensor magnetic terdapat beberapa komponan sesuai dengan jenis dan model flow meternya dan biasanya ini yang menjadi acuan size flow meter dengan koneksi disesuaikan kondisi lapangan apakah menggunakan flange, ulir atau lainya. […]

Kelebihan dan cara instalasi flowmeter magnetic

Kelebihan dan kekurangan flow meter magnetic Karena cara kerja Flow meter electromagnetic dalam mengukur besarnya flow rate berdasarkan luasan penampang maka pressure  aliran tidak akan berkurang , dan karena tidak adanya bagian sensor yang menghalangi atau berputar membuat sensor mempunyai umur yang relatif lebih lama dan free maintenance. Salah satu kelebihan dari magnetic flow meter […]

Flow meter magnetic

Flow meter magnetic atau magnetic flowmeter  dan sering disebut dengan nama magmeter merupakan jenis flowmeter volumetric yang cara kerjanya menggunakan sensor electromagetic berupa electroda. Karena menggunakan sensor elektromagnetic maka flowmeter magnetic ini tidak ada bagian yang bergerak (moving part) dan cocok untuk diaplikasi pada air kotor, air limbah dan air kotor bahkan untuk slurry asalkan cairanya […]

Flow meter portable untuk liquid

Flow meter portable untuk liquid merupakan flow meter yang digunakan untuk mengetahui besarnya aliran air atau debit air dalam pipa yang pengoprasianya mudah dan bisa dibawa ke mana mana karena ringkas dan ringan. Flow meter portable mulai terkenal saat dikenalkanya penggunaan ultrasonic pada aplikasi  flow meter dan dikenal dengan nama portabel ultrasonic flow meter,   dimana […]

 

Ada yang ingin ditanyakan silahkan :

1. Jika ada Pertanyaan tentang Product ataupun harga silahkan langsung hubungi :

 .

2.  Jika ada pertanyaan atau diskusi Tentang tulisan ini silahkan email ke admin@rudywinoto.com

.

Atau silahkan isi kolom dibawah ini dan klik submit  

.  

 

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

w

Connecting to %s

%d bloggers like this: